Phone:+86 13333092057 Email: iasos@iasos.eu
Phone:
+30 6999398373 Email: coyote@iasos.eu
|
|
|
|
|
||
|
Phone:+86 13333092057 Email: iasos@iasos.eu |
Phone:
+30 6999398373 Email: coyote@iasos.eu |
| Vertical
axis wind turbine:
"Iasos IIa". |
Nominal
power: 3,5 KVA |
| Download |
 |
||
| Equipment
included in the wind turbine
|
|
Nominal
power: 3,5 KVA |
 |
|
| Generator
specifications: |
|
| Type: |
Coreless,
axial with permanent
magnets |
| Rated
rotation speed: |
300
rpm |
| Rated
output voltage: |
180
acv |
| Type
coil connection: |
Y |
| Coils
per phase: |
15 |
| Phases: |
Three |
| Pair
of magnets: |
20 |
| Shell
construction material: |
Aluminum |
| Shaft
diameter: |
45
mm |
| Weight: |
43
Kg |
|
Nominal
power: 5 KW |
 |
| The
"charger controller" is used to convert the electric current
produced by the generator into an electric current suitable for charging
the batteries. The buyer should make all the necessary settings on the
"charger controller" so that its operation is efficient, depending
on the available batteries. This "charger controller" has the following technical characteristics: - It has an electronic PWM device to protect the wind turbine from over speed, over voltage and over power. - It has the ability to automatically calculate the maximum capacity of the batteries and automatically calculate the charging rate and maximum charging current. - It is equipped, in addition to the automatic, digitally adjustable, electric braking system and with an autonomous braking system, activated by the user with a switch. - It has integrated BOOST and DUCK technology. The generator installed in the wind turbine has a variable output voltage, depending on the intensity of the wind. When the wind is not strong and the generator voltage is lower than the battery voltage, the "charger controller" automatically increases the voltage to be suitable for charging the batteries (BOOST configuration). Accordingly, when the wind is strong and the voltage of the generator is higher than the voltage of the batteries, then again automatically the "charger controller" lowers the voltage so that it is suitable for charging the batteries (BUCK configuration). - It has integrated MCT and MPPT technologies. When the wind speed is low and therefore the rotational speed of the wind turbine is low, then if the generator is subjected to a heavy load, the rotational speed of the turbine will decrease even more, with negative consequences on the overall efficiency of the system. To avoid this problem, the "charger controller" is equipped with two special electronic devices. One monitors the maximum current power (max current tracking - MCT) and the other the instantaneous power (max power point tracking - MPPT). Thus, by having these two pieces of information, it can automatically adjust the amount of load that the generator can be loaded with, without disturbing the overall efficiency of the system. - Ability to connect to a computer. The serial port enables the interface with a computer, not only for data transfer and analysis, but also for setting the operating parameters. |
|
Nominal
power: 12,8 KW |
 |
|
| The
gear box is used to increase the rotation speed of the generator. The gearbox has an oil temperature indicator and an oil level indicator. The gearbox housing as well as the special oil filling stage are designed to act as a cooling device. The gearbox can be removed and reassembled on the wind turbine in a simple process. The gear box is designed in such a way that it can accept the shock of a violent braking by the electric brake . |
|
| Model: |
"G10046" |
| Nominal
power: |
12,8
Kw |
| Ration: |
1
Χ 4,6 |
| Maximum
inpur torque: |
1.600
Nm |
| Maximum
output torque: |
350
Nm |
| Maximum
input rotation speed: |
76
rpm |
| Maximum
output rotation speed: |
350
rpm |
| Rotation
speed increase steps: |
1 |
| Gears
type: |
Hypoid
gears. |
| Lubricating
oil level indicator: |
Yes |
| Lubricating
oil temperature indicator: |
Yes |
| Amount
of lubricating oil: |
2,5
L |
| Τύπος
λιπαντικού ελαίου: |
90
SAE |
| Type
of lubricating oil: |
Every
three years. |
| Noise: |
Zero |
| Vibration: |
Zero |
| Includes
manual brake disc. |
Yes |
| Includes
the generator connection flange. |
Yes |
| Box
construction material: |
Steel
Q345 |
| Gear
construction material: |
1.7035
Cr4 |
| Shafts
construction material: |
1.7035
Cr4 |
| Inlet
shaft rolling bearings: |
32308
GB 297-94 |
| 30307
GB 297-94 |
|
| Output
shaft rolling bearings: |
33109
GB 297-94 |
| 33108
GB 297-94 |
|
| Power
loss, at an output speed of 300 RPM, is: |
2,31
Nm |
|
Manual
safety brake. |
Model:
"H7010" |
 |
 |
The
manual safety brake stops the turbine shaft. It works by manually rotating
an endless shaft which tightens the two calipers that fit into the brake
disc |
|
 |
 |